There is more to life with TurboRenault.co.uk

Register a free account today to become a member! Once signed in, you'll be able to participate on this site by adding your own topics and posts, as well as connect with other members through your own private inbox!

  • This section contains the archived boards. They should be read only. If you want a thread resurrecting please message admin and we can move into the live section

Front discs from Apec

So are we saying APEC have produced the correct disks or simply copied ones which are incorrect ?

Although readingt the post by Sam, this implies some Vee disks were copied but as yet have not been fitted ?

And finally, are APEC saying they can supply genuine 'sized' disks for fitment to the front of the Vee (materials quality not confirmed) for £47.40 + Vat each ?

Martin
 
James":2pugdm3i said:
It certainly read like these are now the correct size discs made by Apec and rather cheap price.

We haven't seen them and Sam hasn't fitted them yet though ... Can't see the part number on the APEC site though the thread suggests they are supplied non-direct only ... and can't find any google searches on dsk 2779 disks ...

Evidence is what is needed, so will be good to get final validation though :approve:

Martin
 
I could pop up to that place tomorrow and make 100% sure the disks are the right size.

330mm
30mm
28mm min
61 degrees whatever it is and
5 wheel hub holes.

Is that right?
 
Hi guys,

The history is that I sent one of my front discs to apec. They then did their bit (not sure if I can say copied). 8 months or so later they have arrived.

I will put some pics on later when I get home. I wasn't going to fit as I only brought a new set 6 months ago. If any one lives near uttoxeter they are welcome to have a look. Hopefully the pics will help settle a few questions.

Sam
 
Sam Wagstaff":23jqiavl said:
Hi guys,

The history is that I sent one of my front discs to apec. They then did their bit (not sure if I can say copied). 8 months or so later they have arrived.

I will put some pics on later when I get home. I wasn't going to fit as I only brought a new set 6 months ago. If any one lives near uttoxeter they are welcome to have a look. Hopefully the pics will help settle a few questions.

Sam

Great stuff Sam, I guess until they are measured or fitted we won't know for certain but you would assume from what you have done they are correct ... but given the history of false alarms and the massive price difference this almost seems to good to be true - and you know what they say about that ...

I am sure we all have our fingers crossed and well done for your initiative :approve:

Martin
 
I'll send some pics of the pics against a ruler later. I know they are 330x30 and are 5 stud as I quickly measure this yesterday. I'm not sure how to measure other dims like minimun thickness etc...

Like you say with all the history I wouldn't bet anything until they had been fitted and confirmed. The picture that Apec painted to me was that the process to manufacture these is the their norm.

I will be sending a rear disc off this week so hopefully we'll see stock them this year.

Sam
 
Sam Wagstaff":1lmmx9tq said:
I'll send some pics of the pics against a ruler later. I know they are 330x30 and are 5 stud as I quickly measure this yesterday. I'm not sure how to measure other dims like minimun thickness etc...

Like you say with all the history I wouldn't bet anything until they had been fitted and confirmed. The picture that Apec painted to me was that the process to manufacture these is the their norm.

I will be sending a rear disc off this week so hopefully we'll see stock them this year.

Sam

Great stuff Sam, will certainly be a great option for everyone ...

IIRC most of the disk suppliers take cast blanks and machine them to suite specific applications as they don't tend to have foundry capabilities - this means that sourcing the blanks at the correct starting dimensions to allow machining is the key thing. Then it just becomes a tooling and machining exercise to get to the correct dimensions i.e. thickness, offset, diameter, stud and spigot holes etc.

If there are foundries that make the correct sized cast blanks, and these can be sourced easily, then bingo :-) I am not even sure if AP cast their own disk blanks, but would expect so. Hopefully then APEC either cast their own or have found a source.

2 part disks setups are far easier to deal with as you can cast a big flat disk and machine it to any requirements, and also machine bells easily from a billet ... making these two parts in isolation allows manufacturers then to mix & match existing disks and bells to suite an application or simply machine one or more of the two parts to the new requirements. There was a group but for a disk/bell setup which resulted in a Vee specific combination which can now be bought - I think this was compbrake. These are far more expensive at around £400 !

Martin
 
I'm sure there will be lots of us on here that would be very interested in these :approve: it would be great to know if they fit correctly without any problems [cmilie=iconcheers.gif]

Phill
 
I will be sending a rear disc off this week so hopefully we'll see stock them this year

If you do please make sure to specify they are curved vane OEM. Although straight vane would be better than none.

By coincidence we have an account with MACCESS who are the main distributors of APEC discs so if they are correct we should be able to get them cheaply.
They are a low grade disc though but the GTA ones seem to work OK in everyday use.
 
renaultalpine":2pvf2dgi said:
I will be sending a rear disc off this week so hopefully we'll see stock them this year

If you do please make sure to specify they are curved vane OEM. Although straight vane would be better than none.

By coincidence we have an account with MACCESS who are the main distributors of APEC discs so if they are correct we should be able to get them cheaply.
They are a low grade disc though but the GTA ones seem to work OK in everyday use.

Brill :salut: :approve:
 
Here are the photos sorry but the tape measure was a bit faded, you should be able to make them out.

Weight wise I didn't get the scales out but when doing the old 'lift test' I couln't tell the difference.


DSC00035.jpg

DSC00038.jpg

DSC00044.jpg

DSC00046.jpg

DSC00047.jpg

DSC00048.jpg

DSC00049.jpg

DSC00051.jpg

DSC00052.jpg

DSC00055.jpg

DSC00057.jpg
 
ordered mine today £40 plus vat should get them first thing in the morning dont need them but seemed cheap and not one to miss out [smilie=yay.gif]
 
Discs came today look spot on.I am in the motor trade and use apec all the time have had no probs with any components from them.Got them throw my local factor who is a agent for apec i use them alot so got more discount
 
keir v6":150ob18l said:
Discs came today look spot on.I am in the motor trade and use apec all the time have had no probs with any components from them.Got them throw my local factor who is a agent for apec i use them alot so got more discount

Sounds even more promising, the final proof will be fitting. The pictures look great from a diameter, thickness and pad area, the final critical dimension is the offset - from the inside hub mating surface to both disk surfaces ... then bingo ...

Martin
 
Back
Top