bolts

You Will Need - Torque Wrench - T55 Torx socket bit (long and sturdy) Before you start Wind all ten bolts in by hand then out again, this makes sure there's no dirt in the threads. Then if you've got grease with the head bolts, apply some of that to the bolt threads and under the heads of the...

I have had to fit some wheel spacers for my big brake conversion so am hoping to get some longer wheel bolts or even convert to studs? Any suggestions guys?? :?:

I appear to be missing the 4 bolts holding the oil pump on Anyone got a scrap engine they can rescue them from? Or know the sizes and strength of them Thanks

have been burning a bit of oil recently and after some investigating foud out that there were 2 bolts missing from the middle of the rocker cover and oil was leaking down to the spark plugs, decided to replace all the middle 5 while I'm at it but the bolts that came were different to the 3 than...

Are the head bolts on a Dini Turbo reusable? If not is Renault the only place for them? I've tried Payen, British Gaskets and Firstline but no luck with them.

has anybody got these spare? im in need of a full set, for less than £10 please!

Hi All, Has anyone ever bought the head bolt set from Euro Car Parts. I got one of these the other day. It turned up. It had 24 bolts in the set! There should only be 10. Of the 24 there were 2 different sizes. The smallest one seems to be a little bit bigger than the ones that I removed. I...

Anyone know the torque value for the water pump bolts ? All other torque values for cylinder head and attachments are well documented. But no mention of these bolts. Cheers, Andy

.. with the little sachet of grease/locking stuff :lol:

so the other day i noticed the engine rocking back and fourth quite vilantly especially in first at high revs when coming off the gas and going back on. had alook around the mounts and couldnt see a problem so wobbled th engine and it did move back and fourth without much effort. so i took...

hi everyone, Also in need of 3 or 4 torx bolts, those are the ones holding down the cams, just got a couple of rough heads i'd like to sort out? ta

hi guys/ladys iv got to snaped inlet bolts in head!:? are these easy to get out and replace? (not much thread sticking out?)

whats the torque settings for this please? i hate looking through haynes stupid manuals 19 16v of course

hi ya, just done the head gasket on a rover 414 p reg! tightening the bolts how it says in manual, stage 1 15lbf ft stage 2 turn 180dgrees stage 3 a further 180dgrees, does anyone know what the final lbf ft torque setting should be after all 3 stages have been done?

the chunky fine pitch ones that hold the 16V carriers to the hubs... anyone got a set spare?

Does anybody know what sort of bolts hold the front bumper on- the ones that screw upwards under the headlights, my car is too low to check and i havent had time to get it on the ramp at work, ive been told they may be the same as the wing bolts, is this true?? Cheers guys and gals.

How on earth can i get the two bolts on the caliper off so i can change the discs and pads??? I've tried by hand but its pretty stuck :( Cheers Dan

whats the spec of standard clio 1.8 16v wheel bolts? diameter, thread pitch and length? i need to get elongated bolts for my 15mm per side spacers so need to know what the std is and go from there! thing is i want matching bolts and locking ones aswell, so i'll need 6 standard chrome bolts and...

Want to take the cylinder head off to change the head gasket on my RSi but have no idea how to get to the bolts in order to take the intake manifold off. I know that the injection system has to come off but how do I do it. Any kind person out there willing to walk me through it... Thanks in...

Does anyone know where I can get a set of caliper bolts from - there for front calipers off my ph1. The bolts Im after are the torx heads that when you remove allow you to lift up the caliper for acess to the pads. The heads on mine are shot to pieces where Ive used a socket to round over...